How To Install A Breaker Box In A House

Domicile - Diy

How to Install a New Load Center or Breaker Box

The load eye in a abode is the place where whatever excursion in the business firm tin can be turned off. Without the load center to distribute the ability to the various circuits, it would be necessary to turn off all of the electricity in the entire house to work on whatsoever electrical project.

The lugs in a load centre crave an Allen wrench to tighten and loosen them.

The load eye is oftentimes called the breaker box or panel. Some localities require that these boxes exist installed by licensed electricians. If you determine to tackle information technology yourself, make sure that you are familiar with all of the parts of the box before beginning the installation.

• Load center
• 240-volt breakers
• 120-volt breakers
• Screwdriver
• Cordless electrical screwdriver
• Allen wrench
• Wire stripper

1. Locate the electric meter and make sure that the ability is off earlier starting to install the load center. The breaker box can exist installed before the electric meter is in place. However, it is necessary to know where the meter will be located so that the wires from the meter can be put in place when the load center is wired.

2. Remove the face up plate from the load heart by using a screwdriver to extract the screws belongings the face plate to the box. Slide the box between the 2 studs where it volition exist located. The bottom of the box should be nearly four feet above the floor. Using screws and a cordless electric screwdriver, adhere the box on each side to the studs. Depending on the location of the incoming wire from the meter box, slide the electric cables into either the meridian or bottom of the box through the large port in the middle of the edge of the box.

3. Utilize wire strippers to cut away about an inch of the coating from the ends of the three wires. The 2 black cables will be fastened under the lugs in a higher place the main billow. Use a large sized Allen wrench to tighten the lugs onto the wires. The white wire will be similarly attached to the ground bar about the principal breaker. In some installations, all three wires will be black. Make sure to identify which wire is the ground by tracking information technology from the meter box before making these connections.

4. Thread the wires from the various circuits one at a time into the load center. Each wire should exist installed with its respective billow and identified on the circuit list on the door of the box before wiring the next excursion. 120-volt circuits will have 3 wires coming into the box, and most 240-volt circuits volition have 4 wires.

5. Adhere the black wire from a 120-volt circuit to a 120-volt breaker by pushing the terminate of it into the notch under the screw and tightening the screw onto the wire. For 240-volt circuits, there will be ii wires to attach to the breaker. These may be two blackness wires, or a blackness and reddish wire. When the wires are connected to the breakers, clip the breakers to the power bus. All of the white, green, and bare wires from either blazon of excursion volition be inserted under the screws on the ground bar and secured by tightening the screws.

6. Supersede the face plate onto the load eye and install the screws to secure it. Marking the master breaker not to be turned on until all outlets, switches, and fixtures accept been installed. If the meter box is in place, power can be turned on at the meter whenever it is desired afterwards the main breaker has been wired.

Warning

Never install a load middle without turning off the ability at the electric meter first.

The Drip Cap

• The load center in a domicile is the place where any circuit in the house can be turned off.
  
• Some localities crave that these boxes be installed by licensed electricians.
  
• However, information technology is necessary to know where the meter volition be located and so that the wires from the meter tin be put in place when the load centre is wired.
  
• The lesser of the box should exist about 4 feet to a higher place the flooring.
  
• The two black cables will be fastened under the lugs above the principal breaker.
  
• 120-volt circuits volition accept 3 wires coming into the box, and well-nigh 240-volt circuits will accept iv wires.
  
• All of the white, green, and bare wires from either type of excursion will be inserted under the screws on the basis bar and secured past tightening the screws.

Source: https://homesteady.com/12449808/how-to-install-a-new-load-center-or-breaker-box

Posted by: martinezbither.blogspot.com

Share this post